1. Air-entrained concrete masonry material storehouse and materials
原料輸送到汽車工廠、粉煤灰(或砂,石材使用,料斗裝運。 袋裝水泥或散裝水泥倉庫。 當用于加載到料斗。 在化工、化學物質、鋁分別使用分別裝運生產車間。
Raw materials are transported to automobile factories, fly ash (or sand, stone, hopper shipment). Bagged cement or bulk cement warehouse. When used to load into hopper. In the chemical industry, chemical substances, aluminium are used separately in the shipment workshop.
2. Treatment of Aerated Concrete Masonry Material
Fly ash (or sand and cement) electromagnetic vibration feeder, belt conveyor, ground ball ash and fly ash (or sand and cement) pump are sent to storage. Lime is divided into jaws by electromagnetic vibration feeder and belt conveyor.
Crusher, through the barrel of lime decomposition into lime, and then storage, ball screw conveyor grinding into a fine screw conveyor, bucket into powder ingredients. Chemicals in a certain proportion are measured manually.
Certain concentration, storage solution. Aluminum and Aluminum Warehouse Production Workshop, Electric Hoist Pour
Composition Establishment Mixer Mixing into Water, Quantitative Spherical Suspension
3. Ingredients, mixing and pouring of aeration block
The automatic metering of screw conveyor for lime and cement powder proportioning, under the accumulated scale, screw conveyor will add pouring material to mix evenly.
Fly ash (or sand and cement mortar) and waste in measuring barrel are measured. After measurement, the molds with various materials in place can be mixed with slurry. Pre-slurry casting should meet the process requirements (40-deg; c), etc.
If the temperature is not enough, the slurry metering cabinet can be heated by steam. Aluminum suspension can be added 0.51 minutes before pouring.
4. Early and Reduction of Gas Filling Block
鑄造模具與鏈后早期提高室溫,氣體初始頭發50 - 70°c,開始提高1.5 - 2個小時的時間(根據地理優勢,可以使用這種技術在提高早期),負傳播者將框架和身體共同前進好斧頭放在框架的底部的切斷。 鑄造機。 縱向切割工具、車削、銑削、框架掛頭面包對石油的運輸模式、清潔和人工和為下一輛公車集團模具鑄造模具,加上身體后兩層上使用起重機在地板上水壺,水壺今后四層,幾個水壺一輛汽車。 當削減浪費的鑄造機,螺旋輸送機的廢紙漿混合循環廢水機,用于原料。
Casting mold and chain early increase room temperature, gas initial hair 50 - 70 & deg; c, start to increase the time of 1.5 - 2 hours (according to geographical advantages, you can use this technology to improve early), negative propagator will advance the frame and body together, good axe cut at the bottom of the frame. Casting machine. Longitudinal cutting tools, turning, milling, frame hanging bread for oil transportation mode, cleaning and artificial and casting mould for the next bus group mould, plus the use of crane on the floor of the latter two layers of the body kettle, the next four layers of kettle, several kettles and a car. When reducing waste of foundry machine, screw conveyor waste pulp mixing recycling wastewater machine, used for raw materials.
5. High Pressure and Products of High Pressure Gas Block
Before the big pot is in this body, after completion, the organization opens the hot-pressed pot of the kettle, the door inside the reactor is pulled and lifted, and then the kettle automobile crane will be prepared to maintain the high-pressure kettle after completion of the kettle autoclave. Cancel the selection of cranes, and then use to complete the loading depot, empty cars and axe floor kettles hang back into the input network, the backyard and crane in the next cycle.